Product Image |
|
|
|
|
|
| | | |
|
BSA's last part number for these rocker oil feed nuts is 70-1435. All earlier numbers supercede to this one. They should... |
$15.00  |
| | | |
|
New production kickstart spring to suit all later unit BSA and Triumph singles from about '66-on; 250, 441 and 500cc. (If it has a square... |
$19.00 |
| | | |
|
Cast aluminum versions were originally fitted to the very first BSA A7 twin. They're also suitable for just about all Triumph 500/650 pre-unit... |
$65.00 |
| | | |
|
To suit ALL BSA and Triumph 750 triples of the sixties and seventies. Part number is 70-9706. Fabricated in stainless steel, no more problems... |
$14.00 |
| | | |
|
Fashioned after the factory version (61-7014), this lovely stainless steel tool will pull the clutch hub of just about ALL Triumph twins from the... |
$26.00 |
| | | |
|
Fashioned after the factory version (61-3583), this lovely tool will pull the clutch hub of all BSA and Triumph UNIT singles, to my knowledge. ... |
$26.00 |
| | | |
|
Genuine Regina Extra 428 chain, as fitted by most Italian motorcycle factories, years ago. My research shows it should be long enough... |
$22.00 |
| | | |
|
As used on early Terrier and Cub, I believe. Stainless construction, oem part number 421561. |
$11.50 |
| | | |
|
New, perfect, wonderful. All parts constructed of beautiful stainless steel. Includes nuts, studs, and 80# springs. These... |
$57.00 |
| | | |
|
This pair of springs are to suit just about all "automatic advance" ignition units fitted to unit British singles, twins and triples of the... |
$10.00 |
| | | |
|
Unavailable for YEARS. A perfect reproduction of the boot used to cover the pressure switch for the oil warning light, generally used at the... |
$14.00 |
| | | |
|
The ONLY way to reinstall your timing cover with certainty that the seal isn't damaged. Triumph part # 60-1810 (E1810), 28 tpi, constructed of... |
$12.00 |
| | | |
|
Triumph's part number for these valve cover nuts is 70-4610 or E4610, later superceded to... |
$45.00 |
| | | |
|
Triumph part number E4778 or 70-4778, this listing is for the full set of four pieces shown. They should fit all models of UNIT 650 twin... |
$40.00 |
| | | |
|
Triumph part number E4778 or 70-4778, this listing is for the full set of four pieces shown. They should fit all models of UNIT 650 twin... |
$40.00 |
| | | |
|
The ONLY way to reinstall your timing cover with certainty that the seal isn't damaged. Triumph part # 60-0486 (E486), 26 tpi, constructed of... |
$12.00 |
| | | |
|
Exquisite stuff, thread fit and finish are perfect, guaranteed or your money back. Stainless steel construction. So far as I know, these... |
$88.00 |
| | | |
|
Triumph's part number for these valve cover nuts is 71-2744 or E11658. They should fit all UNIT models of unit 500 or... |
$55.00 |
| | | |
|
This auction is for ONE cap. I have a small handful of them, and the second one is shown only to illustrate the cap's underside.... |
$42.00 |
| | | |
|
Brand new production after being unavailable for years, original Triumph part # 70-7578 or E7578, depending on your parts book. This manifold... |
$125.00 |
| | | |
|
Triumph's part number for these side adjustment plugs is 71-2079 or E112079. They should fit 650 Triumph rocker boxes of '71-'72... |
$36.00 |
| | | |
|
A lovely tool. Machined and black oxide coated. Fashioned after an later accessory version of 61-6019, (this one is more complex, but more... |
$76.00 |
| | | |
|
The only way to remove and replace/retorque the large, thin nut that holds on the countershaft sprocket of the 5-speed gearbox, as fitted to twins... |
$60.00 |
| | | |
|
Exquisite. Machined completely from stainless steel, with two-angle relieved jaws to fit in the tight confines of the Triumph timing chest.... |
$89.00 |
| | | |
|
Rear engine mount plates to suit pretty much all Triumph 650 unit machines through 1970. Factory versions were made of stamped and welded... |
$95.00 |
| | | |
|
Perfect and lovely, to suit just about all Triumph unit engines '63-'70, to my knowledge. Styled after the Webco/Jomo racing manifold of... |
$95.00 |
| | | |
|
Triumph's part number for these rocker feed nuts is 70-1435 or E1435. They should fit all models of 650 twin through 1972,... |
$15.00 |
| | | |
|
New production, the manifolds mimic the Webco items of years ago. These manifolds allows the conversion of 650 single-carb heads to twin-carb.... |
$115.00 |
| | | |
|
Triumph's part number for these rocker feed nuts is 21-0550 or S550. They should fit all models of 750 twin from 1973-on, to my... |
$13.00 |
| | | |
|
New, perfect, wonderful. All parts constructed of beautiful stainless steel. Includes nuts, studs, and 110# springs (same as... |
$45.00 |
